|
| One 40 uF and 3 20 uF at 525V sections. Twist-lock mount, 1 3/8 inch (35mm) diameter by 2 1/2 inches (65mm) long. Fits Dynaco ST70, Mk2, Mk4, Scott 299, LK48, LK72 and many other tube amps.Not recommended for use in Dynaco Mk3 or Sunn amps,which really need a 550V or higher rating...(use an SDS Labs capacitor board instead for reliable service).. Fresh new stock made in USA. |
|
|
|
Four 20 uF at 475V sections. Twist-lock mount, 1 3/8 inch (35mm) diameter by 2 inches (52mm) long. Perfect fit for Dynaco PAS2 and PAS3, also Fender Champ, many others. Fresh new stock made in USA. |
|
|
| Replacement sets of speaker terminal strips for dynaco amplifiers. Price includes two terminal strips. |
|
|
| Bias Repair Set for Dynaco ST70 & Mk4.Replaces selenium bias rectifier with silicon diode,
also includes resistors & capacitors used in bias circuit
that are not on the printed circuit board.Not needed on ST70 if you install the SDS Labs Capacitor board |
|
|
| Bias Repair Set for Mark 3Replaces selenium bias rectifier with silicon diode,
also includes resistors & capacitors used in bias circuit
that are not on the printed circuit board.These parts are also included in the Dual Bias Kit on this page.One set required per amplifier |
|
|
| ST70 Offboard Resistor SetThis set includes all resistors in the amplifier that are not mounted on the circuit board. Includes 10ohm 2W biaset resistors, 10k 2W bias supply resistors, 1k 1/2W grid stoppers, 6.8k 2W & 22k 2W power supply resistors, and 470k 1/2W input grid reference resistors. |
|
|
| 15ohm 2W Carbon Film Resistor. Made by Piher in Spain. Great replacement for Original ST70 Biaset resistors to keep the 1.56V biaset. Note, these are sold in a quantity of one so if you are using them for a ST70 you will need to order two of them. |
|
|
| Fits 3/8 inch (10 mm) hole. With insulating washer. Choice of red or black color coding. |
|
|
| Mounts from bottom of chassis. Standard NOS US issue for mounting in a 5/8 inch hole. NOS USA manufacture. You can combine this item with the 7 pin shield to make a 7 pin shielded socket. |
|
|
| 7 pin miniature (British nomenclature B7G) socket for printed circuit board mounting. |
|
|
Standard size 9 pin socket for printed circuit board mounting (3/4 to 13/16 inch pin circle diameter), but has base skirt for a standard "j-slot" shield (sold separately, see below). |
|
|
| Standard size for printed circuit board mounting (3/4 to 13/16 inch pin circle diameter), gold plated pins. |
|
|
| Standard size for printed circuit board mounting (3/4 to 13/16 inch pin circle diameter) |
|
|
Fits holes 1 inch to 1-1/8 inch diameter, mounting holes are on 1 1/2" centers. |
|
|
|
Fits holes 1 inch to 1-1/8 inch diameter, mounting
holes are on 1 1/2" centers. With separate mounting ring, so may be mounted on top or bottom of chassis. |
|
|
| 77-MIP-8 Octal Amphenol Molded In Plate,new,black plastic with plated brass contacts, mounts in conventional 1 1/8" hole with 1 1/2" mounting centers. Made in USA. |
|
| Triode Electronics Inc.
5633 W. Irving Park Road Chicago IL 60634 USA Ph 773-427-8823 (773-HAS-TUBE) Fax 773-327-5652 Open 10 AM to 5 PM CT Monday-Friday |